How to Build Storklinta Dresser

ByShelves Review

You’ve just brought home the STORKLINTA 6-drawer dresser, sleek and modern with smart safety features. Now comes the real challenge: putting it together correctly. This unit uses a unique Anchor and Unlock system with tight tolerances that demand precision and patience.

Affiliate disclosure: We are enrolled in the Amazon Associates Program, and this means we may earn a modest commission if you buy through our referral links—at no extra cost to you.

This guide shows you exactly how to build the STORKLINTA dresser the right way the first time. You’ll learn every stage from unboxing to wall anchoring, including how to install drawer runners, prevent material damage, and confirm the safety lock works as intended.

Unbox and Inspect All Parts

Before picking up a screwdriver, inspect everything carefully. The STORKLINTA ships in three heavy boxes totaling around 145 pounds, so open them on a clean, soft surface to avoid scratches.

Check for All Components

Verify every part against the included manual. Key components include:

  • 2 side panels
  • 1 top panel
  • 1 bottom panel
  • 3 internal partitions with honeycomb core
  • 6 drawer fronts
  • Drawer sides, backs, and fiberboard bottoms
  • Drawer runners
  • Back panel
  • Wall anchoring kit
  • Dowels, screws, and cam locks

⚠️ Common Issue Alert: Reports show missing drawers, cracked faceplates, and damaged particleboard upon delivery. Inspect immediately and keep all packaging until assembly is complete.

If parts are missing or damaged, contact IKEA customer service right away. They typically ship replacements within a few days.

Build the Main Frame

STORKLINTA dresser main frame assembly diagram IKEA

This forms the skeleton of the dresser. Accuracy here prevents problems later, especially with drawer alignment.

Attach Side Panels to Top and Bottom

  1. Lay the side panels flat with the inner side facing up.
  2. Insert dowels into pre-drilled holes on the top and bottom edges of one side panel.
  3. Align the top and bottom panels with the dowels and press down firmly.
  4. Secure using cam locks by turning clockwise until tight. Do not over-tighten because particleboard strips easily.

Repeat for the second side panel.

Install Internal Partitions

The three partitions divide the interior and support drawer runners.

  1. Position the center partition first, which is often wider and houses the Anchor and Unlock mechanism.
  2. Slide it into grooves on the top, bottom, and sides. Ensure it sits flush and vertical.
  3. Secure with provided screws from the outside through the side panels.
  4. Install the two outer partitions the same way, spacing them evenly for drawer support.

✅ Pro Tip: Use a level to confirm partitions are perfectly vertical. Even a slight tilt can misalign drawer runners.

Install Drawer Runners

STORKLINTA drawer runner mounting positions IKEA installation

This is where most assembly fails. Misaligned runners cause drawers that won’t fit or jam during use.

Locate Runner Mounting Points

Runners attach to the inner face of partitions and side panels. Each drawer has a left and right runner.

  1. Match runners to drawer size, as some may vary slightly.
  2. Identify pre-drilled holes on partitions and side panels.

Attach Runners Precisely

  1. Hold the runner in place and ensure it is level and aligned with the holes.
  2. Use the correct screws, usually short coarse-thread types for particleboard.
  3. Do not fully tighten yet, which allows minor adjustments later.

Repeat for all six drawer positions.

⚠️ Warning: If runners are even slightly off, drawers may not slide in. Double-check alignment before final tightening.

Once all are mounted, test-fit one drawer. If it binds or won’t go in, recheck runner position rather than forcing it.

Assemble the Drawers

STORKLINTA drawer component assembly step-by-step IKEA

Each drawer is built from a front, sides, back, and a fiberboard bottom. Precision matters because over-tightening can crack the material.

Step-by-Step Drawer Build

  1. Attach sides to drawer front:
    – Insert dowels into the front panel.
    – Align drawer side and press onto dowels.
    – Lock with cam screws and tighten just until snug.

  2. Attach the back panel:
    – Connect using the same dowel and cam lock method.
    – Ensure corners are square.

  3. Slide in the drawer bottom:
    – The fiberboard base fits into grooves on the sides and back.
    – It should sit flush with no force needed.

Repeat for all six drawers.

✅ Pro Tip: Build one drawer fully, then test it in the frame. If it slides smoothly, use it as a template for the others.

⚠️ Avoid Over-Tightening: Particleboard strips easily. Stop turning when resistance increases.

Insert Drawers and Test Safety Lock

Now comes the moment of truth. Can the drawers slide in, and does the safety system work?

Insert Drawers One by One

Similar Posts